Running in the bearing lubrication and maintenance on a regular basis
Most favorable price : sales@hellerbearings.com
And lubrication of the bearing is the best in the equipment downtime and implementation of the plan and added on a regular basis, at the same time, the old rid grease or via the drain the old oil out empty. Before adding fresh grease injection nozzle should be wiped clean. If there is no zerk bearing box, should open the bearing box cover or end cover, in order to remove the old grease, clean up after, supplement the same type of fresh oil.
2, lubricating oil
Check the oil level of lubricating oil and oil, in general, a normal oil level equipment oil level Windows or mark a third - two-thirds of range. Oil compensating way for oil cup, the display of the oil level represents oil compensating ability, and the bearing box oil level is to meet operation requirements, oil cup CPC a lower than a quarter of its total volume filling oil may be considered.
Check and repair method oil, remove a small amount of oil as a sample and fresh oil, has the ability to unit may be considered for oil testing, to ensure the oil qualified. If the sample looks like clouds, so may be mixed with water as a result, people often say that oil emulsification, at this time should replace the lubricating oil.
If the sample cheng dark color or thick, then may say lubricating oil has begun to carbonization, should be replaced the old oil thoroughly. If possible, use fresh oil to wash oil. Oil change, should ensure that the replacement with new and old the same type of lubricating oil, adding the meet the requirements of oil level.
Use of the lubrication system of oil bath type, if the oil temperature 60 ℃ (below 140 ° F), and no pollution of lubricating oil, lubricating oil a year once. If the oil temperature in 60-100 ℃ (140-210 ° F), need to change four times a year, lubricating oil. If the oil temperature at 100-120 ℃ (210-250 ° F), monthly need to replace a lubricating oil. If the oil temperature at 120 ℃ (250 ° F) above, the need to change once a week of lubricating oil.
The correct installation and maintenance is an important factor for normal operation of bearing, at the same time, must pay attention to maintain the purity of the bearing. Bearings must prevent polluted by contaminants and moisture, must have a correct installation and lubrication. In addition, the design of the bearing arrangement, the condition of the oil seal, the form of a lubricant and change cycle and special maintenance also play an important role, must be attention.
234407BM 234706BM 234406BM 517/2860V/YA 5610/2500 517/1720X1V 527/1181M 510/1180M 517/930 510/670 590/560 510/500 52780 59080 517/368M 51760U 517/238 6207-2ZN 6206-2ZN 6205-2ZN 6204-2ZN 6203-RZ 6203-2ZN 6202N 6202-2ZN 6201-2ZN 6200ZZ 6200-2ZN 62/32-ZN 62/32-Z 62/32N 62/32-2Z 62/32-2RZ 62/32-2RS 62/28-2RZ 62/22-2RZ 61996 61992 61988 61984
We can provide free samples . Please contact Email for any inquiries
1, grease lubricationAnd lubrication of the bearing is the best in the equipment downtime and implementation of the plan and added on a regular basis, at the same time, the old rid grease or via the drain the old oil out empty. Before adding fresh grease injection nozzle should be wiped clean. If there is no zerk bearing box, should open the bearing box cover or end cover, in order to remove the old grease, clean up after, supplement the same type of fresh oil.
2, lubricating oil
Check the oil level of lubricating oil and oil, in general, a normal oil level equipment oil level Windows or mark a third - two-thirds of range. Oil compensating way for oil cup, the display of the oil level represents oil compensating ability, and the bearing box oil level is to meet operation requirements, oil cup CPC a lower than a quarter of its total volume filling oil may be considered.
Check and repair method oil, remove a small amount of oil as a sample and fresh oil, has the ability to unit may be considered for oil testing, to ensure the oil qualified. If the sample looks like clouds, so may be mixed with water as a result, people often say that oil emulsification, at this time should replace the lubricating oil.
If the sample cheng dark color or thick, then may say lubricating oil has begun to carbonization, should be replaced the old oil thoroughly. If possible, use fresh oil to wash oil. Oil change, should ensure that the replacement with new and old the same type of lubricating oil, adding the meet the requirements of oil level.
Use of the lubrication system of oil bath type, if the oil temperature 60 ℃ (below 140 ° F), and no pollution of lubricating oil, lubricating oil a year once. If the oil temperature in 60-100 ℃ (140-210 ° F), need to change four times a year, lubricating oil. If the oil temperature at 100-120 ℃ (210-250 ° F), monthly need to replace a lubricating oil. If the oil temperature at 120 ℃ (250 ° F) above, the need to change once a week of lubricating oil.
The correct installation and maintenance is an important factor for normal operation of bearing, at the same time, must pay attention to maintain the purity of the bearing. Bearings must prevent polluted by contaminants and moisture, must have a correct installation and lubrication. In addition, the design of the bearing arrangement, the condition of the oil seal, the form of a lubricant and change cycle and special maintenance also play an important role, must be attention.
