the key requirements of fag thin-walled bearing lubricating grease amount
Most favorable price : sales@hellerbearings.com
234407BM 234706BM 234406BM 517/2860V/YA 5610/2500 517/1720X1V 527/1181M 510/1180M 517/930 510/670 590/560 510/500 52780 59080 517/368M 51760U 517/238 6207-2ZN 6206-2ZN 6205-2ZN 6204-2ZN 6203-RZ 6203-2ZN 6202N 6202-2ZN 6201-2ZN 6200ZZ 6200-2ZN 62/32-ZN 62/32-Z 62/32N 62/32-2Z 62/32-2RZ 62/32-2RS 62/28-2RZ 62/22-2RZ 61996 61992 61988 61984
We can provide free samples . Please contact Email for any inquiries
For sealing the thinwall bearings, the production has been filled in the appropriate oils, open seal set on the host, in order to prevent grease leakage. Note that fat content is too low, it is easy to lead to a lack or a dry rub, fat affect life expectancy. Fat can cause excessive temperature rise. Grease a large leak, not only pollute the environment, and waste. Therefore, access to thin-bearing grease the better FAG Bearing, in order to ensure adequate lubrication.
Lubrication of mechanical friction: friction resistance, in the thin film formed on the surface of a part. Cooling temperature: heat away through the oil flow to prevent sintered. Clean up: the flow of oil to clean the working surface friction parts and metal production of other materials. seal leak-proof: to reduce gas leakage and external pollutants. Rust and Corrosion, can be adsorbed on the surface, in order to prevent water and air, acid gases, and the contact area. Buffer: a sharp rise in pressure, the engine cylinder head, piston, and the sudden, connecting rod and piston pin on the crankshaft oil can withstand load when the load buffer.
Grease is a directly apply the grease to thinwall bearings between the sports surface. However, in the roller bearings to FAG road surface of work input and slide grease, must follow the following 5 principles:
(1) grease cutting thinwall bearings must be the work of the bearing surface and internal clearance, so that you can make the grease lubrication.
(2) In FAG Bearing surface of the work you should keep a certain amount of grease, and a certain amount of time, but also to prevent loss due to excessive grease.
(3) grease of the input and output of the flow and sealing requirements to be a consensus that this is conducive to invasion the dirt out.
(4) to ensure good lubrication, grease to minimize the usage.
(5) grease opened exit hole to end, so that the additional grease can squeeze on an old grease to ensure a good lubrication. In particular, the reminder to FAG bearing with grease, and the time you want to note that 10 million thinwall bearing grease the operating temperature range, and if you are not in a suitable temperature in the range, then it will be counterproductive.
Lubrication of mechanical friction: friction resistance, in the thin film formed on the surface of a part. Cooling temperature: heat away through the oil flow to prevent sintered. Clean up: the flow of oil to clean the working surface friction parts and metal production of other materials. seal leak-proof: to reduce gas leakage and external pollutants. Rust and Corrosion, can be adsorbed on the surface, in order to prevent water and air, acid gases, and the contact area. Buffer: a sharp rise in pressure, the engine cylinder head, piston, and the sudden, connecting rod and piston pin on the crankshaft oil can withstand load when the load buffer.
Grease is a directly apply the grease to thinwall bearings between the sports surface. However, in the roller bearings to FAG road surface of work input and slide grease, must follow the following 5 principles:
(1) grease cutting thinwall bearings must be the work of the bearing surface and internal clearance, so that you can make the grease lubrication.
(2) In FAG Bearing surface of the work you should keep a certain amount of grease, and a certain amount of time, but also to prevent loss due to excessive grease.
(3) grease of the input and output of the flow and sealing requirements to be a consensus that this is conducive to invasion the dirt out.
(4) to ensure good lubrication, grease to minimize the usage.
(5) grease opened exit hole to end, so that the additional grease can squeeze on an old grease to ensure a good lubrication. In particular, the reminder to FAG bearing with grease, and the time you want to note that 10 million thinwall bearing grease the operating temperature range, and if you are not in a suitable temperature in the range, then it will be counterproductive.
