Full-function CNC bearing heater
Most favorable price : sales@hellerbearings.com
Eddy heat effect principle use this machine in a large transformer short-circuit loop current of the motor, the introduction of European and American technology and related electronic devices, high-precision temperature sensors, electronic numerical display. Control bearings (set) temperature heating selection parameter table accurately using metal thermal expansion principle, bearing (set) to provide data and fit the shaft and smooth assembly.
First, the main structure:
Host from the power transformer, moving core (matching), temperature actuators, electronic digital display and other components of CNC.
Second, the use and operation:
1, in accordance with the requirements of the bearing sleeve and the shaft in the parameter selection table from Richard heating temperature.
2, according to the diameter size of the bearing, choose a different stem diameters, and moving core spin on the heater panel, heating the bearing sleeve in moving core core column, and then the panels together along with moving core core columns Push the transformer to form a closed magnetic circuit.
3, the power of the heater switch to the appropriate sub-file gear, plug in the power, according to the bearings, bushings inside diameter size, the heating time can be completed within 30-3 seconds.
4, the temperature sensor plug into the heated end of the core base sensor socket, then the sensor temperature sensor on the inner ring bearings or bushings and bearings against the thermal head and the table above board, it good contact for accurate temperature measurement.
5, open digital display temperature controller and turn on the power switch, heating start temperature digital display continuously displays bearing the heating temperature, when the temperature rose to a predetermined desired temperature, you can cut off the power, pull out the core, remove the bearing panel , set into the shaft to be assembled, shall completed.
Fourth, note:
1, the heater is heating up fast. When powered on, to closely monitor the temperature display, when the temperature rose to a predetermined value, immediately turn off the power, in order to avoid damage to the bearing temperature microstructure.
2, after use, you want to push the digital display temperature into the machine, so as not to break something and cut off all power.
3, remove the heated bearings must pay attention to safety, to prevent burns.
234407BM 234706BM 234406BM 517/2860V/YA 5610/2500 517/1720X1V 527/1181M 510/1180M 517/930 510/670 590/560 510/500 52780 59080 517/368M 51760U 517/238 6207-2ZN 6206-2ZN 6205-2ZN 6204-2ZN 6203-RZ 6203-2ZN 6202N 6202-2ZN 6201-2ZN 6200ZZ 6200-2ZN 62/32-ZN 62/32-Z 62/32N 62/32-2Z 62/32-2RZ 62/32-2RS 62/28-2RZ 62/22-2RZ 61996 61992 61988 61984
We can provide free samples . Please contact Email for any inquiries
Bearing is an important component widely used in mechanical transmission, but in assembling the repair process, due to tolerances required to produce the "interference" caused great difficulties to operate normally applied to the bearing external pressure or flame heating, heating or cooking oil with the most primitive technique which uses a hammer and other methods, this method is easy to cause the shaft to be galling, the bearing is damaged, the noise increases, reduced service life, while energy consumption, higher labor intensity defect, for the latest factory developed YG51-DKQ-I ~ V type full-function electronic CNC bearing sleeve heater to solve this problem, which is a national initiative in bearing applications in the field. For heating bearings diameter range is 115-200mmEddy heat effect principle use this machine in a large transformer short-circuit loop current of the motor, the introduction of European and American technology and related electronic devices, high-precision temperature sensors, electronic numerical display. Control bearings (set) temperature heating selection parameter table accurately using metal thermal expansion principle, bearing (set) to provide data and fit the shaft and smooth assembly.
First, the main structure:
Host from the power transformer, moving core (matching), temperature actuators, electronic digital display and other components of CNC.
Second, the use and operation:
1, in accordance with the requirements of the bearing sleeve and the shaft in the parameter selection table from Richard heating temperature.
2, according to the diameter size of the bearing, choose a different stem diameters, and moving core spin on the heater panel, heating the bearing sleeve in moving core core column, and then the panels together along with moving core core columns Push the transformer to form a closed magnetic circuit.
3, the power of the heater switch to the appropriate sub-file gear, plug in the power, according to the bearings, bushings inside diameter size, the heating time can be completed within 30-3 seconds.
4, the temperature sensor plug into the heated end of the core base sensor socket, then the sensor temperature sensor on the inner ring bearings or bushings and bearings against the thermal head and the table above board, it good contact for accurate temperature measurement.
5, open digital display temperature controller and turn on the power switch, heating start temperature digital display continuously displays bearing the heating temperature, when the temperature rose to a predetermined desired temperature, you can cut off the power, pull out the core, remove the bearing panel , set into the shaft to be assembled, shall completed.
Fourth, note:
1, the heater is heating up fast. When powered on, to closely monitor the temperature display, when the temperature rose to a predetermined value, immediately turn off the power, in order to avoid damage to the bearing temperature microstructure.
2, after use, you want to push the digital display temperature into the machine, so as not to break something and cut off all power.
3, remove the heated bearings must pay attention to safety, to prevent burns.
